View CPCI500D-1_4445354.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

cPCI500 Series
500W 6Ux4HP DC/DC CompactPCITM Power Supply
S SELECTION GUIDE Model Number CPCI500D-1 C CPCI500D-2 C C CPCI500D-3 C CPCI500D-4 CPCI500D-5 C Power 500W 500W 500W 500W 500W 500W 500W 500W 500W 500W 500W 500W Output Current 5V 55A 30A 30A 55A 55A 30A 55A 30A 30A 55A 55A 30A 3.3V Y N N Y N N Y N N Y N N 12V 11A 11A 11A 11A 11A 11A 11A 11A 11A 11A 11A 11A -12V 1.7A 1.7A 1.7A 1.7A 1.7A 1.7A 1.7A 1.7A 1.7A 1.7A 1.7A 1.7A IPMI N N Y Y N N N N Y Y N N Ish1 P P A A A A P P A A A A No No No No No No Yes Yes Yes Yes Yes Yes
FEATURES
6Ux4HP package 500W power at 0-50C C PICMG 2.11 compliant RoHS compliant Widerange 36-72Vdc input range nput IPMI option Active or passive current sharing ent 47-pin I/O Connector 80% efficiency No minimum load Hot-swap capable
C CPCI500D-6 CPCI500D-1C C CPCI500D-2C C CPCI500D-3C C CPCI500D-4C C CPCI500D-5C C CPCI500D-6C C
INPUT CHARACTERISTICS Parameter Input Operating Voltage Input Voltage Withstand Inrush Current 36Vdc input 72Vdc input Conditions Min 36 34 Typ Max 72 75 25 50 Units Vdc Vdc Apk Apk
DESCRIPTION
The cPCI500 is a high-reliability, 500W, 6ux4HP CompactPCITM power supply operating from widerange DC-input. The use of our patented V-Series topology yields high efficiency which consequently permits packaging of this product in a compact, single card slot format (4HP). ORing diodes and current sharing allow the cPCI500 to be operated in N+n parallel-redundant configurations. Available with an IPMI interface option, the cPCI500 was designed for hot-swap, redundant configurations to support high-availability (HA) telecom applications. With a widerange input of 36-72Vdc, safety agency approvals to UL60950 and EN60950, EMI compliance to ETSI and Telcordia standards, the cPCI500 was designed with globally-deployed systems in mind. Additional features include remote sense compensation, unit enable control (EN#), output inhibit control (INH#), output fault signal (FAL#), and thermal warning signal (DEG#). LEDs are provided for visual indication of input power presence and output fault condition. The 4HP package and complement of global safety agency approvals provide for an advanced, high-density, high-efficiency power solution for your CompactPCI requirements. OUTPUT CHARACTERISTICS Output V1 V2 V3 V4 Parameter Temperature Coefficient PARD (V1 & V2) PARD (V3 & V4) Output Power Output Power Transient Response Over-Voltage Protection Minimum Load Output Holdup Tim Remote Sense Compensation Current Share Tolerance Full load, low line V1, V2 & V3 V1-V3; full load Pri-Sec
For full details go to www.murata-ps.com/rohs
Nominal Voltage +5.0Vdc +3.3Vdc +12Vdc -12Vdc Conditions
Output Current Min 0A 0A 0A 0A Min Max A 55A 30A 11A 1.7A Typ Max B 30A 60A 11A 1.7A Max 0.02
Total Regulation1 1% 1% 1% 3% Units %/C mVp-p mVp-p W W %Vnom sec %Vnom A
20MHz bandwidth 20MHz bandwidth 50C, 400lfm airflow 70C, 400lfm airflow V, 50% load step Settling time All outputs 0 12 300 125 0 0 120
50 180 500 250 8 200 135
16
msec mV
10 4 1.5 500
% kVac kVac Vac
Isolation Notes:
Pri-Chassis Sec-Chassis
1 Total regulation includes line, load, and cross regulation.
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
www.murata-ps.com
TDC_cPCI500 Series.B01 Page 1 of 4
cPCI500 Series
500W 6Ux4HP DC/DC CompactPCITM Power Supply
GENERAL CHARACTERISTICS Parameter Efficiency Switching Frequency MTBF Weight PROTECTION Parameter Thermal Shutdown Output Power Limit Input Protection Over-voltage Protection Conditions/Response Automatic recovery upon restoration to operational temperatures Automatic recovery Internal line fuse, Littlefuse BLN 25P ROHS or equivalent Output V1, latching Output V2, latching Parameter Output Overload Protection Conditions/Response Outputs are individually protected against overloads and indefinite short circuit with automatic recovery upon removal of the fault condition. Design Verification Testing (DVT) confirms that voltage excursions on the output buses resulting from insertion/extraction events do not exceed the specified maximum of 5%. However, routing of power and signal lines in the mating backplane is critical to minimization of such excursions. In addition, performance can be critically affected by load characteristics including resistance, negative resistance, and reactive components. While the control loop responses have been designed for optimum hot-swap performance over a wide range of characteristics, there may be instances where the voltage excursions exceed published specifications. In such cases, the control loop responses can be modified to perform optimally. Output isolation devices are present in all outputs to isolate faults within a failed power supply. 6.0 3.9 6.5 4.3 Inception Min Typ 90 530 25 7.0 4.7 Max Units C W A Vdc Vdc Calculated per MIL-HDBK-217F, 25C, ground benign Unpackaged 84 3.6 Conditions 48Vdc input, 500W load (dependent upon load profile) Min Typ 65 72 Max Units % kHz khrs kg
Hot-Swap Capability
Output Fault Isolation
STATUS & CONTROL SIGNALS & INDICATORS Name Hot-Swap Enable Output Inhibit DC Good Description Short pin on connector will enable the outputs when the mating pin is tied to DC GRD. Supply will not power up until this pin is engaged to its mate in the backplane. Unit output will be inhibited as pin is disengaged from the mating connector. Secondary referenced; active low, TTL compatible. Logic "0" or short circuit to Logic RTN (pin 40 or 43) inhibits all outputs. Secondary referenced. Open collector signal with an internal 2.2k pull-up resistor is connected to the +5V output. TTL signal will transition high when all outputs are between 90% and 110% of their nominal voltage. Connection of the sense leads across the load at the desired point of regulation will compensate for voltage distribution drops up to 700mV between the output terminals of the power supply and the point of connection. The unit reverts to local sensing if the sense lines are opened for any reason. The output is protected against shorted or open leads. Applies to all outputs. Secondary referenced; TTL compatible; active low. Signal transitions to a Logic 0 denotes a thermal warning. A green LED will be illuminated when the input voltage is present and above the minimum requirement. A green LED will be illuminated when the output voltages are within 90-110% of specification, coincident with assertion of the DC Good signal. This LED will be extinguished if any of the output voltages is outside of this range. A green LED will be illuminated when the fan is operational, coincident with de-assertion of the Fan Alarm signal. This LED will be extinguished in the event of a fan failure. A power supply generated signal used to simultaneously start power supplies connected in parallel when the load on any output exceeds a single power supply's capacity for that output. These pins must be bused together at the backplane in parallel/redundant applications (N+n) when N>1. In simple redundant (1+1) or non-parallel applications (1+0), the pin can be ignored. This pin presents a DC ground signal to the mating pin in the backplane. It is intended to be used by the system to detect the presence of a power supply when the supply is mated into an available position.
Remote Sense Fan Alarm Power Present Indicator LED DC Good Indicator LED Fan Good Indicator LED
Sync Start
Power Supply Present
ENVIRONMENTAL CHARACTERISTICS Parameter AmbientOperatingTemperature Ambient Storage Temperature Humidity Operating; non-condensing Storage; non-condensing Altitude Operating. De-rate ambient temperature by 2C per 1000ft above 5000ft. Storage Cooling Self-cooled by internal fan Conditions De-rate output power linearly above 40C to 250W at 60C. Min 0 -25 10 5 -200 -200 Typ Max 60 +125 95 95 10000 40000 Units C C % % ft ft
www.murata-ps.com
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
TDC_cPCI500 Series.B01 Page 2 of 4
cPCI500 Series
500W 6Ux4HP DC/DC CompactPCITM Power Supply
CERTIFICATIONS Agency/Characteristic UL CSA VDE CE RoHS SELV Vibration Shock ELECTROMAGNETIC COMPATABILITY (EMC) Conducted Emissions Electrostatic Discharge (ESD) Radiated Immunity Conducted Immunity Line Voltage Surge EN 300 386, NEBS GR-1089 EN61000-4-2, Level 3, Criteria B EN61000-4-3, Level 3, Criteria A EN61000-4-4, Level 3, Criteria A EN61000-4-5, Class 3, Criteria B Standard UL1950 CSA950 (per cUL) EN60950 LVD Directive; self-certified EN Directive 2002/95/EC; self-certified; see Selection Guide table for specific model compliance Self-certified MIL-STD-810F, Method 514.5, Procedure I; self-certified MIL-STD-810F, Method 516.5, Procedure I; self-certified
MECHANICAL DIMENSIONS
www.murata-ps.com
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
TDC_cPCI500 Series.B01 Page 3 of 4
cPCI500 Series
500W 6Ux4HP DC/DC CompactPCITM Power Supply
PACKAGE SPECIFICATIONS
CONNECTOR Pin #1 1-4 5-12 13-18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 Staging2 M M M M M M M M M M M S M M M M M M M M M M M M M M M M M L M M Signal Name V1 RTN V2 RTN V3 V4 RTN RESERVED RTN GA0 RESERVED EN# GA1 V1ADJ V1 SENSE GA2 V2ADJ V2 SENSE S RTN V1 SHARE V3 SENSE IPMB SCL DEG# INH# IPMB SDA V2 SHARE FAL# IPMB PWR V3 SHARE CGND ACN/+DC IN ACL/-DC IN Description V1 Output V1 and V2 Return V2 Output V3 Return V3 Output V4 Output Signal Return Reserved V4 Return Geographic Address Bit 0 Reserved Enable Geographic Address Bit 1 V1 Adjust V1 Remote Sense Geographic Address Bit 2 V2 Adjust V2 Remote Sense Sense Return V1 Current Share V3 Remote Sense IPMB Serial Clock Line Degrade Signal Inhibit IPMB Serial Data Line V2 Current Share Fail Signal IPMB Power Input V3 Current Share Chassis Grnd (Safety Grnd) AC Input Neutral/+DC Input AC Input Line/-DC Input
IPMI/IPMB POWER SUPPLY SATELLITE CONTROLLER FEATURES
Complies with IPMI V1.5 Rev 1.1 and IPMB V1.0 Complies to PICMG2.9 (CompactPCI Systems Management Specification) 8 Analog inputs configured for monitoring voltages and currents on power supply outputs V1 - V4 Monitors the state of the thermal sensor Output inhibit control can be overwritten by IPMI commands Self Test with LED indicator (can be read and overwritten by IPMI commands) 6 programmable thresholds on each analog sensor Each threshold on each sensor can be enabled to generate event messages if that threshold is crossed Thermal sensor can be enabled to generate event messages Responds to all mandatory IPMI commands and numerous optional commands as indicated in the functional specification Firmware can be upgraded via the IPMB bus Includes Device SDR's (Sensor Data Records) - These specify the type of sensor for each input (voltage, current, temperature, etc.) as well as the conversion formulas from raw ADC data to voltages, currents, etc. Includes FRU type information such as Model Number, serial number and firmware creation date MECHANICAL Shock: MIL-STD-810d, Method 516.3, Procedure 1. Vibration: MIL-STD-810d, Method 514.3, Procedure 1. Dimensions: 6U x 4HP x 160mm (see Mechanical above) EMC & SAFETY EMI: NEBS Compliant, ETSI Compliant Safety Agency Ratings Input Voltage: 48 VDC Input Current: 15A Input Power: 620W Agency Approvals UL1950/CSA950, EN60950, CE Mark. (Low Voltage Directive)
NOTES: (1) Pin numbers correspond to the female backplane connector. (2) L = Long Length Pin (First Make, Last Break); M = Medium Length Pins; S = Short Length Pins (Last Make, First Break)
SAFETY AGENCY RATINGS Input Voltage Input Current Input Power 36-72Vdc 25-12.5Adc 620W
USA: UK: France: Japan:
Mansfield (MA), Tel: (508) 339-3000, email: sales@murata-ps.com Milton Keynes, Tel: +44 (0)1908 615232, email: mk@murata-ps.com Montigny Le Bretonneux, Tel: +33 (0)1 34 60 01 01, email: france@murata-ps.com Tokyo, Tel: 3-3779-1031, email: sales_tokyo@murata-ps.com Osaka, Tel: 6-6354-2025, email: sales_osaka@murata-ps.com Website: www.murata-ps.jp Shanghai, Tel: +86 215 027 3678, email: shanghai@murata-ps.com Guangzhou, Tel: +86 208 221 8066, email: guangzhou@murata-ps.com
Canada: Toronto, Tel: (866) 740-1232, email: toronto@murata-ps.com
Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Tel: (508) 339-3000 (800) 233-2765 Fax: (508) 339-6356
www.murata-ps.com email: sales@murata-ps.com ISO 9001 REGISTERED
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. (c) 2008 Murata Power Solutions, Inc.
Germany: Munchen, Tel: +49 (0)89-544334-0, email: munich@murata-ps.com
China:
05/14/08
www.murata-ps.com
Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000
TDC_cPCI500 Series.B01 Page 4 of 4

▲Up To Search▲

Price & Availability of CPCI500D-1

	To Download CPCI500D-1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .